August 2026  ·  Phoenix Drywall Repair LLC

How Much Does Drywall Repair Cost in Phoenix? (Real Numbers)

The most common question we get: "How much does it cost?" Fair question. The honest answer is that it depends — but that's not a cop-out. Drywall repair pricing varies for legitimate reasons, and understanding those reasons helps you evaluate quotes and avoid getting overcharged or underserved.

Here are real numbers from the Phoenix market, broken down by job type.

Minimum Charge

Almost every professional drywall contractor has a minimum charge. Ours is $200. Below that, the math doesn't work — drive time, setup, materials, and cleanup have a fixed cost regardless of how small the repair is. Any legitimate licensed contractor is going to have a similar floor. If someone quotes you $75 for a drywall patch, ask about their license.

Small Patch (nail holes, doorknob holes, small impacts)

Typical range: $200–$350

This covers a single small repair — a doorknob hole, a couple of nail holes, a small crack. At this price you're paying for the minimum: show up, patch, texture, done. Many homeowners at this level wonder if it's worth hiring out vs. DIY. For anything under 2 inches, DIY is reasonable. For larger holes or anything that needs texture matching, professional results are hard to achieve without experience.

Medium Repair (6–24 inch hole, section of wall)

Typical range: $300–$600

A hole from a plumber's access cut, a section of damaged drywall from a picture mount failure, or a crack that runs along a seam for several feet. These jobs require a backing board or California patch, proper taping, and texture matching across a larger area.

Full Sheet Replacement

Typical range: $600–$900 per sheet

When damage is extensive enough that cutting out and replacing a full 4x8 sheet is more efficient than patching, pricing reflects the full process: demo, hang, tape, multiple mud coats, texture, and prime. Labor is the majority of this cost — the sheet itself is $15–$30.

Water Damage Repair

Typical range: $600–$3,000+

Wide range because scope varies widely. A ceiling stain from a small drip that dried before causing structural damage is at the low end. A section of wall that was saturated, developed mold, and requires full replacement plus framing inspection is at the high end. Multi-room water damage events can exceed this range significantly.

Post-Mold Remediation Rebuild

Typical range: $1,500–$6,000+

When a mold remediation company cuts out drywall across multiple areas of a home, rebuilding it is a multi-day project. Single room: $1,500–$2,500. Multiple rooms or extensive cutting: $3,000–$6,000+. Insurance typically covers this when the underlying water event was covered.

Smooth Wall / Skim Coat

Typical range: $500–$6,000+

Single room: $500–$1,200. Whole house (1,500–2,500 sq ft): $2,500–$6,000. The skill involved in getting a flat, uniform finish that holds up under Arizona's raking sunlight is why this isn't cheap. A bad skim coat is immediately obvious.

Popcorn Ceiling Removal

Typical range: $400–$4,000+

Single room: $400–$900. Whole house: $1,500–$4,000. Price goes up if the ceiling is painted (harder to scrape) or if asbestos testing/abatement is required for pre-1978 homes.

Why Do Quotes Vary So Much Between Contractors?

A few legitimate reasons:

• License status — unlicensed contractors carry no overhead for licensing, insurance, or bonding. Their prices look attractive until something goes wrong.
• Texture matching skill — contractors who can match texture well charge more. Ones who can't, don't.
• Scope interpretation — two contractors may scope the same job differently. Make sure you're comparing apples to apples.
• Materials — quality of joint compound, primer, and tools varies. Cheap materials show up in the finished product.

The cheapest quote is rarely the best value. The most expensive isn't always justified either. Look for a licensed contractor with clear communication, a firm timeline, and references you can actually call.